smarthomatic

User Tools

Site Tools

Trace:
soil_moisture_meter

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
soil_moisture_meter [2015/01/06 17:35] – [Buildup of PCB] breaker27soil_moisture_meter [2015/01/29 22:43] – [Partlist (in buildup order)] breaker27
Line 14: Line 14:
 |    1     | Transceiver PCB RFM12B                  | IC2        |  {{ parts:ic_rfm12b.jpg }}                   | |    1     | Transceiver PCB RFM12B                  | IC2        |  {{ parts:ic_rfm12b.jpg }}                   |
 |    1     | IC 74HC14D                              | IC3        |  {{ parts:ic_smd_74hc14d.jpg }}              | |    1     | IC 74HC14D                              | IC3        |  {{ parts:ic_smd_74hc14d.jpg }}              |
-|    1     | Connector AVR Mini ISP 6pin             | JP1        |  {{ parts:connector_isp.jpg }}               |+|    1     | Connector AVR Mini ISP 6pin             | JP1        |  {{ parts:connector_mini_isp.jpg }}               |
 |    1     | Connector pin header (for serial TX debugging etc.)  | JP3   |  {{ parts:connector_pinheader.jpg }}  | |    1     | Connector pin header (for serial TX debugging etc.)  | JP3   |  {{ parts:connector_pinheader.jpg }}  |
 |    1     | Antenna (82,2mm wire)                   | ANT        |  {{ parts:antenna.jpg }}                     | |    1     | Antenna (82,2mm wire)                   | ANT        |  {{ parts:antenna.jpg }}                     |
 |    1     | LED 2mA                                 | LED1       |  {{ parts:led_yellow.jpg }}                  | |    1     | LED 2mA                                 | LED1       |  {{ parts:led_yellow.jpg }}                  |
-|    1     | Resistor 220R                           | R1, R6     |  {{ parts:resistor_smd_603.jpg }}            | +|    1     | Resistor 560R                           | R1         |  {{ parts:resistor_smd_603.jpg }}            | 
-|    1     | Resistor 1M                             | R4         |  {{ parts:resistor_smd_603.jpg }}            | +|    1     | Resistor 1M                             | R2         |  {{ parts:resistor_smd_603.jpg }}            | 
-|    1     | Resistor 100k                           | R5         |  {{ parts:resistor_smd_603.jpg }}            | +|    1     | Resistor 100k                           | R3         |  {{ parts:resistor_smd_603.jpg }}            | 
-|    1     | Switch                                  | S1         |  {{ parts:switch.jpg }}                      | +|    1     | Switch                                  | S1         |  {{ parts:button.jpg }}                      |
 ===== Buildup of PCB ===== ===== Buildup of PCB =====
  
Line 33: Line 32:
   - Now connect a multimeter to **check the power consumption**. Press the button when the device starts up. The device will blink some seconds very fast and then go to power down mode. **The device should draw only ~0.1µA.** If the current is much higher, you may have a short circuit somewhere.   - Now connect a multimeter to **check the power consumption**. Press the button when the device starts up. The device will blink some seconds very fast and then go to power down mode. **The device should draw only ~0.1µA.** If the current is much higher, you may have a short circuit somewhere.
   - Solder the debug TX pin, the RFM12B module and antenna with a soldering iron as usual.   - Solder the debug TX pin, the RFM12B module and antenna with a soldering iron as usual.
 +  - Switch on the device and check power consumption again. With connected RFM12, it should now be ~1.7µA.
  
 {{https://raw.github.com/breaker27/smarthomatic/develop/hardware/soil_moisture_meter/placing.png?500}} {{https://raw.github.com/breaker27/smarthomatic/develop/hardware/soil_moisture_meter/placing.png?500}}
soil_moisture_meter.txt · Last modified: 2015/01/29 22:43 by breaker27